What working area is published for VIC1325F?
The area is 1300*2500mm. Compare the full incoming blank and layout with both dimensions in the intended orientation.
Laser Cutting Machine
VIC1325F — VIC-F Laser Cutting Machine
VIC1325F has a published working area of 1300*2500mm in the VIC-F CO2 laser cutting family. The description identifies a fully enclosed cutting area, CO2 head and tube, linear guides, stepper motors and belt drive. Its specification table lists an 80-600W laser power range and Ruida control with USB.
Connect the worktable selection to the actual production layout when requesting an offer. The shape of the incoming blank and the arrangement of finished parts should be visible together. This gives the supplier a defined basis for discussing the support surface and access to the proposed enclosed cutting area.
Technical specifications
| Specification | VIC1325F |
|---|---|
| Working Area | 1300*2500mm |
| Laser Type | CO2 Laser |
| Working Table | Knife Table or Honeycomb Table |
| Laser Power | 80-600W |
| Power Supply | 220V/50HZ, 110V/60HZ |
| Min Line Width | ≤0.15mm |
| Position Accuracy | 0.01mm |
| Repetition Accuracy | 0.02mm |
| Cutting Speed | 150mm/s |
| Control System | Ruida (USB Interface) |
| Graphic Format Support | PLT, DXF, BMP, JPG, AI, etc |
Configuration options vary by model. Confirm the final specification, selected components and operating requirements with your quotation.
Other models in this series
VIC1325F working area and equipment structure
The VIC1325F working area measures 1300mm by 2500mm. In the same family, VIC1318F lists 1300*1800mm and VIC1530F lists 1500*3000mm. Compare the full layout with those rectangles in its intended orientation. Obtain external equipment dimensions separately, because the working-area figures do not define the installation footprint.
Knife or honeycomb tables appear as alternatives. The configuration narrative describes aluminum blades for the knife-table arrangement. Identify the proposed surface in the enquiry and ask for it to be stated in the quotation. The source does not say that both surfaces are included or provide a load rating for your planned setup.
A fully enclosed cutting area is a described structural feature. If handling the blank requires a particular access arrangement, explain that requirement and ask for the relevant dimensions. Do not use the enclosure label alone to decide how the material is introduced, how the equipment is installed or what documentation applies to the offer.
Planning work with VIC1325F enclosed cutting area
For an application discussion, specify the actual material and thickness with the finished outlines. Give any relevant dimensional limits and the required appearance of cut edges. These are requirements for review; neither the model category nor the published area demonstrates a tested processing result for that particular material and drawing.
Suppose a layout contains small finished shapes within a much larger blank boundary. Send the complete arrangement and the individual part drawings, identifying which shapes form the required output. Ask for the proposed support surface and equipment access to be reviewed together, rather than treating an individual small part as the full description of the job.
VIC1325F configuration
Supported graphic formats include PLT, DXF, BMP, JPG and AI. Give the production file its units, scale and revision, and attach a view of the intended arrangement. Ruida and USB are the published control and interface entries; the preparation and interpretation of your specific drawing should still be clear in the enquiry.
The power supply entries are 220V/50HZ and 110V/60HZ. Confirm which version is required at the destination, together with the selected laser power and worktable. The power range is selection information, not a complete equipment schedule, and the two supply entries do not establish automatic switching between electrical systems.
Position Accuracy is listed as 0.01mm, Repetition Accuracy as 0.02mm and Cutting Speed as 150mm/s. Keep the required finished dimensions and production target separate from these fields. Use one identifiable drawing and material specification as the basis for comparing proposals, and record any change to the support arrangement explicitly.
Product questions
Which larger same-family area can be compared?
VIC1530F lists 1500*3000mm. Check the actual layout and proposed access arrangement before selecting that alternative.
Which table arrangement is described with aluminum blades?
The knife-table configuration uses the aluminum-blade description. Knife or honeycomb alternatives are listed; the offer should identify the chosen surface.
Does the enclosure label determine the loading arrangement?
No specific loading method follows from the structural description alone. Explain your handling requirement and request details for the proposed equipment.
What should accompany a worktable-selection enquiry?
Send the complete layout, individual outlines, material, thickness and required result. Identify the support surface being considered and keep the drawing revision clear.
Related equipment and information
Ready to discuss VIC1325F?
Share your material, dimensions and process. Start a conversation about the right configuration.